The BBP-2 is a complete kit for replacing press fit bottom bracket bearings, cups, and adaptors. Includes a press assembly and compatible fittings for removing and installing most press fit bottom bracket configurations. The BBP-2 includes: - 6 sets of precision-machined bushings (in 9 sizes) to fit most bottom bracket configurations - 8 precision-machined extractor cups and 5 hardened collets for compatibility with most bearing IDs and bearing/cup ODs - 8 installation drifts for standalone bearing installation - Press assembly with comfortable handle, oversized shaft, and magnetic back plate for quick and easy assembly - Organized in two convenient storage cases The full list of bushing/collet/drift dimensions for bearing compatibility can be found on the instructions/parts diagram. NOTE: The BBP-2 consists of the BBP-1.2 Bottom Bracket Bearing Press Kit and BBP-AOS Bottom Bracket Bearing Extractor Add-On Set, both of which are available separately. However, the BBP-AOS requires the BBP-1.2 for use.
The 761s Reaming and Facing Cutters are used to machine head tubes using integrated headsets with a 42 mm bearing and 45 degree angular contact used by the Campagnolo® Hiddenset standard. FSA® and other manufacturers also make headsets in this standard. Includes upper and lower cutters.
Proper frame preparation is very important. Park Tool's Head Tube Reaming and Facing Set combines reaming and facing of the head tube to create a perfect fit for most sizes of head cups. Includes: • 30.1 mm reamer (part #751.2) and four different size pilots (29.8mm, 30.0mm, 33.8mm, and 36.8mm) • 690 facer • Quick-release, quick-adjust feature: bottom portion slides off and on easily without threading SHIS terminology: The HTR-1 as stock will face frames of EC29, EC30, EC34 and EC37. It will ream frames of EC30. Accessories will allow service in other standards.
Proper frame preparation is very important. Park Tool's Head Tube Reaming and Facing Set (33.8mm reamer) combines reaming and facing of the head tube to create a perfect fit for most sizes of head cups. The HTR-1B comes with a reamer of 33.9mm for the 1-1/8 inch headset standard. Includes: • 33.9mm reamer (part #754.2), and four different size pilots (29.8mm, 30.0mm, 33.8mm, and 36.8mm) • 690 Facer • Quick-release, quick-adjust feature: bottom portion slides off and on easily without threading SHIS terminology: The HTR-1B as stock will face frames of EC29, EC30, EC34 and EC37. It will ream frames of EC34. Accessories will allow service in other standards.
To ensure proper headset performance and longevity, special attention must be given to accurately machine the fork’s crown race seat. Park Tool's Crown Race Cutting Tool is a professional-quality machining tool for milling both the outer edge and lower surfaces of the crown race seat. • Includes high speed steel cutters and adjustable collets to machine 26.5mm and 27.1mm crown race seats on 1” forks and 30.1mm crown race seats on 1-1/8" forks • Unique adjusting system allows a tight fit of the tool on any fork, threaded or unthreaded (even forks with externally butted steerer tubes), ensuring a smooth, accurate cut and proper alignment of the fork in the frame • Cutter sized for 1-inch standard is part #845 (sold separately) • Cutter for 1-1/8 inch standard is #846 (sold separately)
The BBP-AOS is used in conjunction with the BBP-1.2 Bottom Bracket Bearing Press Kit to extract press fit bottom bracket bearings, cups, and adaptors. The BBP-AOS utilizes an expanding collet and extractor cup system to safely remove bearings without requiring impact. Also included are eight installation drifts for pressing bearings into pre-installed cups. - 8 precision-machined extractor cups and 5 hardened collets for compatibility with most bearing IDs and bearing/cup ODs - 8 installation drifts for standalone bearing installation - Organized in a convenient storage case - Full list of compatible bearing inner/outer diameters found on instructions/parts diagram NOTE: The BBP-AOS requires the BBP-1.2 Bottom Bracket Bearing Press Set for use. The BBP-1.2 and BBP-AOS are also available as a complete set (part # BBP-2).
The SHX-1 Slide Hammer Extractor is a professional solution specifically designed for removing press fit cartridge bearings from bicycle components. Utilizing expanding collets, an extendable shaft, and a substantial (960g) slide hammer, the SHX-1 securely yet forcefully drives out cartridge bearings with targeted impact. The SHX-1 is compatible with cartridge bearings with inner diameters from 6 to 32 millimeters, covering most press fit applications found on bicycles including hubs, suspension linkages, and bottom brackets. - Set of 5 expanding collets covers most bicycle bearing IDs from 6mm to 32mm - Slide hammer shaft is extendable from 6.5" (165mm) to 13" (233mm) for additional force when needed - Organized in a convenient storage case
Park Tool's Bottom Bracket Facing Set is designed to be a complete self-contained facing set, combining top-quality precision parts with ease of use. Simply install the threaded inserts using the facer handle, then insert the facing tool through the guides and install the tension spring and speed nut. After applying a liberal amount of cutting oil, the BFS-1 easily cuts the shell material, giving you a clean, faced surface. Now you're ready to install the bottom bracket. The English threading inserts are included. The Italian threading (36 x 24) inserts are available as an accessory, as part #688. Two are required.
Frame and Fork Taps will become a lifesaver at some time for virtually every mechanic. These taps are made of high-carbon steel and are precision ground. Park Tool's Frame and Fork Taps cut easily and fit conventional tap handles. - Tap-12.1: 12Mm X 1.0 - Tap-12.2: 12Mm X 1.5 - Tap-12.3: 12Mm X 1.75 - Tap-15.1: 15Mm X 1.0 - Tap-15.2: 15Mm X 1.5 - Tap-20.1: 20Mm X 1.0 - Tap-20.2: 20Mm X 1.5 - Tap-20.3: 20Mm X 2.0
- The HBP-1 is designed to quickly and accurately press bearings into a wide variety of cartridge bearing-type bicycle hubs. - Quick release design for fast tool installation and removal - Includes two bearing presses and precision machined aluminum pilots, bushings, and spacers - Works with more than 20 different cartridge bearing sizes and multiple axle configurations
The 791 Reamer Set reamer is used on the PF30 frame shells. The reamer is sized at 45.94mm. The 791 Reamer Set must used with the HTR-1 Head Tube Reamer and Facer, a 750.2 Centering Cone and the 690-XL Facer. The 791 set also includes a pilot that allows a facing-only option of the PF30 frame shell.
$305.32 - $338.74
Park Tool's Right Hand Bottom Bracket Tap is a replacement tap for their BTS-1 Bottom Bracket Tap Set (sold separately). This tap is used on the non-drive or left side of the bike, which uses a clockwise or "right hand threading." Two taps are required for use.
Park Tool's 752 Reamer and Spacer Set allows reaming of bottom bracket frame shells in the BB30 standard. The reamer is sized at 41.94mm. It is used with the HTR-1 Head Tube Reamer and Facer and a 750.2 Centering Cone (each sold separately). The set includes a spacer to stop the reaming depth.
Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.
The BX-2.2 features updated pallet configuration and storage options to help you keep your tools secure and easily accessible. The expanded custom designed tool pallets, including dual-sided pallet wings, are all housed in a virtually indestructible composite travel case. Designed and built for the traveling mechanic who demands the best! - Custom designed tool-holding pallets with loops and pockets - Folding, dual-sided pallet wings - Front tool pallet that stores securely inside during transport - Dent-proof composite shell built around an aluminum frame - Key lock - Nominal dimensions: 19" x 14.85" x 8.5" (48.25 cm x 37.7 cm x 21.6 cm), 13.2 lbs. (6 kg)
Build your own tool by adding cutters, reamers and facers to Park Tool's HTR-HS (cutters, reamers, and facers sold separately). It includes handle and shaft, quick release center cone and nut. -Quick-release, quick-adjust feature: bottom portion slides off and on easily without threading -Optional accessories include over 20 different reamers and facers for numerous headset and bottom bracket standards
The SBK-1 is a professional level kit for installing and removing cartridge bearings in bicycle suspension pivots. A comprehensive set of 27 precision-machined hard-anodized guides enables compatibility with a wide range of bearing inner and outer diameters. Combined with our proven bearing press design, the SBK-1 quickly and easily pushes the old bearing out of the linkage and reinstalls the new bearing precisely and squarely. - Magnetic back plate for easy configuration and assembly - Organized in a convenient storage case Includes extractor cups/drifts for the following ODs: - 16mm - 17mm - 19mm - 20.6mm - 21mm - 22mm - 22.3mm - 24mm - 26mm - 28mm - 28.6mm - 30mm - 32mm - 35mm Includes extractor studs and pilots for bearings with the following IDs: - 8.5–9mm - 10mm - 12mm - 12.7mm - 15mm - 17mm - 20mm NOTE: For bearing extraction, the SBK-1 requires a minimum of 3mm of flat linkage structure outside the bearing to support the extractor cup/drift. For bearings without this flat structure, consider using the Park Tool SHX-1 Slide Hammer Bearing Extractor.
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
Park Tool's Crown Race Cutter Adaptor is used in conjunction with the CRC-1 Crown Race Cutting Tool (sold separately) to machine 39.8mm crown race seats (1.5” standard) on tapered forks with 1-1/8” steerer tubes. It includes a precision-machined adaptor body and a 39.8mm high-speed steel crown race cutter. The CRC-15 will work on forks with a maximum 1.5-inch taper of 4.25 inches.
Upgrades the DT-5 to the DT-5.2. - Four telescoping axle adaptors - Two stand off studs for Flat Mount alignment - 12mm front fork thru axle sleeve
Park's HHP-2 accurately aligns and presses 1-, 1-1/8-, 1-1/4- and 1.5-inch headset cups into your frame's headtube. It features a quick-release design for fast tool installation and removal, extra-long handles for superior leverage and stepped bushings for precise cup alignment. This versatile tool also presses cartridge bearings and cups into one-piece bottom bracket shells and holds fixed-cup wrenches in place when removing or installing adjustable-type bottom brackets.
A perfect way to start a bicycle tool collection! A great combination of tools to help a home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-4 includes more than 15 genuine Park Tool products that can perform dozens of tasks and includes a custom Park Tool toolbox with extra room for spare parts and more tools. The SK-4 includes: - AWS-10 Fold-Up Hex Wrench Set - BBB-4 Big Blue Book of Bicycle Repair - CC-3.2 Chain Checker - CN-10 Professional Cable and Housing Cutter - CT-5 Mini ChainBrute Chain Tool - FR-5.2 Cassette Lockring Tool - GSC-1 GearClean Brush - HCW-16.3 Chain Whip/Pedal Wrench - HR-8 8mm Hex Wrench - MLP-1.2 Master Link Pliers - SD-2 Shop Screwdriver: #2 Phillips - SW-7.2 Triple Spoke Wrench - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench
$120.52 - $154.22
Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.
The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. The MWR-SET includes 6mm to 17mm wrenches with a 12-point two-way ratcheting box end. Forged from chrome vanadium steel, chrome-plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful! - Includes 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, and 17mm wrenches
Designed and built specifically for a wide variety of bicycle hex work the THH-1 is a set of eight common sizes of professional quality T-Handle hex wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite hex set, the THH-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - 2, 2.5, 3, 4, 5, 6, 8 and 10mm hex wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or over-sized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")
The BKD-1 Hydraulic Brake Bleed Kit will bleed most models of DOT-fluid-based hydraulic brakes. Hydraulic systems need bleeding to remove any air bubbles and to inject new, clean fluid. - Designed and built for home use and the rigors of daily commercial use - Includes two syringes, hoses with shutoff clips, multi-size bleed blocks and a unique attachable syringe mount - Housed in a rugged reusable case - Machined stainless steel and 7075 aluminum fittings to service SRAM, Hayes, Formula, Hope and other brands of DOT-fluid-based hydraulic brake systems - Replacement parts available - Brake fluid not included
Designed and built specifically for a wide variety of bicycle Torx compatible work, the THT-1 is a set of eight common sizes of professional quality T-Handle star-shaped wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite Torx compatible set, the THT-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - T6, T8, T10, T15, T20, T25, T30 and T40 Torx compatible wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The Park Tool TW-5.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). With a range of 2-14Nm, the TW-5.2 is designed for the lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.
Page 1 of 10 Next page