Parts

Super-smooth steering, quality materials, cutting-edge design and serious durability are all hallmarks of Cane Creek's 40-Series headsets. • Technical Description: ZS44/28.6/H8/K|ZS56/40/H4/K • Top Type: ZS - ZeroStack • Top Head Tube Inside Dia.: 44.00mm • Stem Clamp Dia.: 28.6mm • Top Stack Height: 8mm • Top Bearing Type: Black Oxide, Sealed • Bottom Type: ZS - ZeroStack • Bottom Head Tube Inside Dia.: 55.95mm • Crown Race Seat Dia.: 39.79mm • Crown Race Type: Steel, Face-Sealed • Bottom Stack Height: 4mm • Bottom Bearing Type: Black Oxide, Sealed • Material: 6061 aluminum • Weight: 109g

The Hellbender 70 bottom bracket utilizes a bearing made of 440C stainless steel, providing exceptional ride quality and reliability. The stainless steel bearing in the Hellbender 70 strikes a perfect balance between value and lasting performance. - 440C stainless steel bearings, dual lip seal, marine grease - Machined aluminum cups

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 12mm - Outer Diameter: 24mm - Width: 6mm

Cinelli Cork tape is available in many colors and includes plugs. - Plugs included

Compatibility: Shimano Ultegra, Br-GRES805, BR-GRE505.

Compatibility: Shimano XTR, XT, SLX, M985, M785, M666, S700 2011+

- Cast steel calipers, ideal for MTB and hybrid cycles - Includes rubber boots and brake noodles - Linear pull - 20.6 - 40.6mm reach - Front & Rear - Black - Boot & Noodle - 20.6-40.6mm

The CLOUT 1 hydraulic brake system has the capability of a much higher end brake in the market, providing the rider with greater power, consistency and feel, all at a price that is designed to compete with entry level bikes. The CLOUT1 operates on mineral oil and features a 2 piston caliper with an ergonomic design lever assembly with REACH ADJUSTMENT.

BRAKE DISC CLK CMD-23 MECH F&R 160mm BK - OEM quality replacement disc brake set for MTB and Hybrid bikes - Includes front and rear caliper and 160mm disc rotors - Complies with and exceeds CEN regulations - Large pad area for improved braking performance

Size-specific enthusiast-level platform pedal provides optimal shoe/pedal interface. - Optimal surface area - Minimal profile 16mm thin - 10 adjustable pins per side for grip - Premium bearings & seal system - Stamp small recommended for shoe sizes: 5-10 (us); 37-43 (EU) - Stamp large recommended for shoe sizes: 10-15 (us); 43-49 (EU) Specs: - Spindle material: forged scm 435 chromoly steel - Body material: 6061-T6 aluminum - Inner bearing type: IGUS LL-glide bearing - Outer bearing type: Enduro cartridge bearing - Footprint: 114mm x 111mm (Large); 100mm x 100mm (Small) - Weight: 470g per pair (Large); 415g per pair (Small) - Warranty: 5 years

Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals

Crank Brothers' Premium MTB Cleats are perfect for your Crank Brothers Eggbeater, Candy, Acid, Smarty, Mallet, and Quattro pedals. They're made from solid brass for crisp entry and exit, and top-notch durability. - SPD compatibility - Weight (pair): 30g - Float: 6 degrees - Release angle: 15 or 20 degrees

Crank Brothers' most versatile pedal. The Candy excels at it all – cyclocross, XC, trail, all mountain. 4-sided entry enables superior mud-shedding capability, and customizable float and release angles create a dialed-in feel. - Spindle material: Forged scm 435 chromoly steel - Body material: One piece composite - Wing material: Stamped steel - Spring material: 300 series stainless steel - Release angle: 15° / 20° - Q-factor: 52mm - Inner bearing type: Igus LL-glide bearing - Outer bearing type: Enduro cartridge bearing - Cleat: Premium brass cleats with shims included - Weight: 294g per pair - Warranty: 5 years

Crank Brothers Mallet DH, the choice of DH world champions. - Concave platform for secure foothold - 8 adjustable pins per side for grip - Traction pad technology customizable interface - Ribbed body for better traction when unclipped - Chamfered edges to reduce rock-strikes - 57mm q-factor for stability at speed - 4-sided entry / superior mud shedding - Customizable float and release angle - Premium bearings and double seal system - Spindle material: Forged scm 435 chromoly steel - Body material: 6061-T6 aluminum - Wing material cast: Stainless steel - Spring material 300 series stainless steel - Release angle 15° / 20° - Max rider weight no restriction - Q-factor 57mm - Inner bearing type IGUS LL-glide bearing - Outer bearing type enduro cartridge bearing - Cleat premium brass cleats with shims included - Adjustable pins 8 per side for grip - Endcap hex alloy - Weight: 479 grams

Turn any 8-10 speed HG-splined cassette hub into a 3/32-inch 16-tooth singlespeed.

Bearings for maintaining and rebuilding DT Swiss hubs. - DT Swiss 6902 Bearing

- Clamps to a threadless steerer, offers up to 3-1/4" stem height increase - Forged 6061 aluminum - Threaded alloy top cap

- Gel inserts and foam padding provide maximum comfort in this saddle - Cut out assists in eliminating pressure - Water resistant and reflective logos make the saddle both safe and durable

Dimension Seatpost Binder Bolts - 16g

Heavy duty bolt-on aluminum seatpost clamp.

Dimension Nylon Basic Toe Straps -Durable metal buckle -Multi-purpose strap can also be used as a lash strap for bike touring or rear rack (caution must be used to keep the strap tail out of the wheel) - 450mm

Dimension American bottom bracket for one-piece cranks. - Include cups, bearings and cones - 24 tpi

Dimension Junior Pedals. - Molded nylon, 1-piece, caged-type pedals - Built-in reflectors, will not accept toe clips - Overall pedal size is 80 x 60mm - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Platform - Spindle Material: Chromoly Steel - Weight: 230g (9/16-inch); 304g (1/2-inch)

Dimension Toe Clips and Straps Set. Includes: - 4 bolts - 4 nuts (washers included) - 2 nylon toe straps - 2 toe clips

Dimension classic 4-hole cruiser chainwheel, with offset to allow chainline adjustment. - Classic 4-hole cruiser chainwheel - Offset ring allows chainline adjustment - Polished steel - Fits 1-piece crankarms - Requires 1/2-inch x 1/8-inch chains

Dimension City Pedals. - Built-in reflectors, will not accept toe clips - Molded nylon; 1-piece, caged-type pedal - Slip-resistant surface

Dimension Mountain Basic Pedals. - Molded nylon 1-piece, caged-type pedal with reflectors - Accepts toe clips - Hang tag packaging - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 330g

Dimension Seatpost Clamps - Diameters: 28.6mm, 30.0mm, 31.8mm, 35.0mm - Weight: 34g

Dimension Chainrings. - No ramps, pins, or shift aids

An quick way to make a bike more comfortable, Dimension High-bars come in four different rises for inexpensive and easy bar-height changes. - Four rise options available from 30-100mm - AL-6061 aluminum alloy - ISO4210 Safety Tested for City/Trekking use - Not recommended for use with bar-ends or clip-on aero bars - 15-degree sweep

Dimension Two-Bolt Seatposts provide a sturdy and durable saddle perch for cross country and all-mountain riding in three diameters, rigorously tested to ISO 4210 Mountain standards. - Constructed with AL-6061-T6 aluminum - Shot-peened finish - 0mm offset

Dimension Mountain Compe Pedals. - Forged aluminum body - Accepts toe clips - Pedal Body Material: Aluminum - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 335g

For cross country and all-mountain riding, Dimension Mountain bars provide generous—but not ridiculous—width, rigorously tested to ISO 4210 Mountain standards. - Shot-peened finish - 6061-T6 Aluminum - 9-deg backsweep - 720mm wide - 35mm rise

For cross country and all-mountain riding, Dimension Trail Stems provide a broad array of sizing options, rigorously tested to ISO 4210 Mountain standards. - Constructed with AL-6061-T6 aluminum - Shot-peened finish - Dimension stems are not intended for use with carbon handlebars or carbon steerer tubes

Dimension Combo Pedal Sets are assembled with size large toe clips, straps and reflectors. - Pedal Body Material: Aluminum - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 520g

Dimension 31.8 Stems are fully forged 6061-T6 aluminum stems that have a 4-bolt handlebar clamp. - 31.8mm can be used with 26.0 bars with additional shim (SM5317) - Dimension stems are not intended for use with carbon handlebars or carbon steer tubes - Weight: 130g-180g

Dimension Suspension Seatpost - Clamp Style: Std Rails - Diameter: 27.2mm - Length: 350mm - Material: Aluminum - Max Height: 255mm - Min Height: 130mm - Offset (mm): 0mm - Seatpost Type: Suspension - Travel (mm): 35mm - Weight: 450g

For cross country and all-mountain riding, Dimension Trail Stems provide a broad array of sizing options, rigorously tested to ISO 4210 Mountain standards. - Constructed with AL-6061-T6 aluminum - Shot-peened finish - Dimension stems are not intended for use with carbon handlebars or carbon steerer tubes

Dimension Multi Speed Chainrings. - CNC-machined AL-7075 - Has ramps and pins to aid in shifting (not on 74mm BCD inner chainring) - Same BCD as Surly Long Haul Trucker, Cross-Check, and Troll complete bikes (74mm & 110mm)

Dimension cassettes feature Shimano/SRAM compatible spacing, precise fitment for crisp shifting, and easy installation with standard tools. They're a perfect replacement for worn out cogs. Constructed of steel cogs and lock ring. Cassette Cogs: - 11 – 28T: 11-13-15-18-21-24-28 - 12 – 28T: 12-14-16-18-21-24-28 - 12 – 32T: 12-13-15-18-21-24-32

Dimension cassettes feature Shimano/SRAM compatible spacing, precise fitment for crisp shifting, and easy installation with standard tools. They're a perfect replacement for worn out cogs. Constructed of steel cogs and lock ring. Cassette Cogs: - 11 – 28T: 11-12-13-15-17-19-21-24-28 - 11 – 32T: 11-12-14-16-18-21-24-28-32 - 11 – 34T: 11-13-15-17-20-23-26-30-34

Dimension Rigid Mountain Forks are intended for general recreational riding only; they are not intended for aggressive riding, stunt riding or road racing. - Forged dropouts with eyelets - Chromoly tubing - Cantilever mounts only (no disc mount) - Axle to Crown Length: 395mm - Brake Mount (Fork): Canti Studs - Color: Black - Crown Race: 30 - Front Axle: 10mm x 100mm - Maximum Tire Clearance (Fork): 3.8 - Offset: 45mm - S.H.I.S. Stem Clamp Diameter: 25.4-24 tpi Quill - Steerer Tube Length (mm): 140 - Steerer Type: Straight - Weight: 877g - Wheel Size: 26-inch

Recommended for grip shift and riders looking for the best shock absorbing grip in the industry. 60 grams, standard grip length - 5 1/8", installed DIA. 32mm, weight plus or minus 5%, 1 set of bar plugs included. - 60 Grams - Standard Grip Length – 5 1/8" - 32mm - Weight plus or minus 5% - Made for 22mm bars (can fit applications down to 19mm) - Bar Plugs included - *Install Bar Plugs first for the protection of grips and ease of installation

- Multi-position stem to fine tune your riding position - 3D forged 6061-T6 aluminum - 4-bolt oversized handlebar interface - Includes top cap and angle adjustment shims (2)

Add some classic style to your favorite rig with Electra's Hand-Stitched Grips. You'll love their stylish hand stitching and long-lasting comfort.

Get back on the road with a quality replacement hanger. - Attachment hardware is sold separately - For specific compatibility concerns, please contact our Customer Service team Specifications: - Size: Rear drive side, 135mm Q/R - Mounting location: Rear drive side - Attachment: 2-bolt - Weight: 12g

Grab life by the handlebars. Enjoy a life behind bars. Customize your bike with a new handlebar that fits your own personal style. For style, comfort or both. - Polished finish - Sturdy steel construction - Size: 760mm x 200mm - Clamp: 22.2mm

Electra's Comfort XL Saddle provides extra comfort with its wider seating area. And, its plush padding is paired with a durable cover and double chrome springs to smooth out even the roughest roads.

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

- Grade 10 chromium steel balls

More support with more comfort Why not combine the best? With the GA3, the winged grip has proven its genius to the All-Mountain world. The special thing about the GP1's off-road cousin is, he locks on tight with a lightweight inner clamp. The concept combines all the relief benefits of the wing and actively supports your wrist. Your freedom of movement and the accompanying bike control remains fully intact. Riding pleasure guaranteed! What exactly are the benefits of the wings on the grips? The longer a ride is, the harder it is for a rider to maintain the ergonomically correct hand position on the bike. As a result, riders often bend their wrists too much, stressing nerves and tendons and inhibiting blood circulation. Numbness and pain in your hands are often the undesirable consequences. The GA3 grip optimizes the hand position through the Miniwings and prevents over-bending in your wrist. What is the carpal tunnel? The carpal tunnel is an anatomic passage in your wrist for nerves and tendons running from the lower arm to the hand. If the wrist is bent too much the nerves become constricted, which often leads to pain and numbness. The GA3 with Miniwing is based on the well-established and proven design of the MTB-specific GA2 grips. The particular shape of the grips provides you with great comfort and grip, without compromising the freedom of movement. This allows you to have all the control you need to tackle the most demanding of trails with full confidence. As an ergonomically perfected expansion of the GA-series by Ergon, the primary purpose GA3 grips is to provide relief out in the trail. But, they're not only perfect for the MTB category, they are also ideal on fitness-oriented and urban bikes. The ergonomic winged-grip GA3 is available in five striking colors. Ergon grips don't just feel great, they look great, too!

- Woven nylon fiber material - Double hold system for strength - Durable for urban or MTN riding - Fits most BMX platform style pedals - Anti-slip adjustable design

- AL6061-T6 lightweight alloy construction - Fits 22.2mm diameter bars - Length: 130mm - Weight: 127g

- Supreme AirForm Foam Padding - Max Comfort Elastomer Suspension - Steel Rails - Water Resistant Vinyl Cover - Dimensions: 260 x 218mm

- AirForm Foam Padding - Dampening Rail Suspension System - Steel Rails - Water Resistant Vinyl Cover - Dimensions: 274 x 137mm

- Shimano SPD-SL-style - Engineered thermoplastic injection body - Anti-slip walk pads - Fixed position with no float

- Shimano SPD-SL-style - Engineered thermoplastic injection body - Weight of 24 grams per cleat - 4.5-degree floating arc

FSA (Full Speed Ahead) Polycarbonate Headset Stack Spacers

This is an FSA Self Extracting Crank Bolt for Hollow Carbon MegaExo Light Cranks - Designed to fit hollow carbon FSA cranks only - Includes M17 bolt, M27 self-extracting cap, and washers